1. Contractor's Choice for Quality Scaffolding Since 1992

       

       
       
      CONSTRUCTION EQUIPMENT
      MASONRY | STUCCO | CONCRETECOMPACTIONGENERATORSAIR COMPRESSORS | AERIAL LIFTS
      Masonry
       
      Stucco  

      Concrete

       

      Vibrators

      Trowels
      WALK-BEHIND POWER TROWELS

      To function properly, power trowels must maintain a precise perpendicular relationship between the gearbox's output shaft and blad arms. Once that relationship is compromised, the trowel will vibrate and/or wobble. MBW has gone to great lengths to maintain this critical relationship. MBW Walk-Behind Power Trowels feature the industry's heavist bearings, output shafts, gears, spiders and blade arms. Comparison of these critical MBW components to those of any competitor answers the question as to why MBW trowels run so well for so long.

      specifications
      f36/4
      ENGINE OPTIONS Honda GX 240 8 hp (6kw)
      RING DIAMETER 36 in (91cm)
      TROWEL SPEED 70 - 135 rpm

      specifications
      f46/4
      ENGINE OPTIONS Honda GX 240 8 hp (6kw)
      RING DIAMETER 46 in (117 cm)
      TROWEL SPEED 70 - 135 rpm

       

      Vibrator

      Vibrators

      Vibrator-Motor

      Vibratory-Plate-Reversible

      W. Rose Trowels
      W. Rose Trowels
      HANDLE Leather
        Softgrip
        wood
      SIZES 11" - 13"
      rose trowel

      All wet screeds tested by MBW exposed operators to excessive hand/arm vibration. The ScreeDemon's patent pending mount retention method enables use of low durometer isolators without loss of operator control. Hand/arm vibration is 50 to 90% lower than competitive screeds.


      Specifications WS500H
      OPERATING WEIGHT 29 lbs (13.2 kg)
      ENGINE MAKE Honda GX31TA2
      MAX RATED POWER 1.5 hp (1.12 kW) @ 7000 rpm
      DISPLACEMENT 1.9 in³ (31 cm³)
      FUEL TANK CAPACITY 0.17 gal (0.64 L)

      Available Float sizes range from 8ft. to 16ft

       BACK TO TOP OF PAGE

      screedemon

      Compaction
      Rammers
      The R420 & R440 Series Rammer is ideally suited for the compaction of granular, mixed, and cohesive soils in confined areas. A mainstay in many municipal fleets, the R420 & R440 offer highly productive percussion rammers at less than 126 or 142 lbs. respectively. The contoured fuel tank provides the largest fuel capacity in its class and effectively baffles engine noise. Power is supplied by either a 2.4 hp 4-cycle Robin engine or a 3 hp 4-cycle Honda engine.

      • Up to 3800 lbs of force
      • 4-cycle engine
      • Elevated bellows placement for trench applications
      • Polyethylene slide bearings provide minimal internal wear
      • 10" or 11" high density, die cast aluminum tamping shoe
      • 4" and 6" trench shoes available
      • Patented anti-vibration handle standard on the 420H 

      Specifications F46/4
      SHOE SIZE 10 x 11.5 in (25 x 29)
      OPERATING WEIGHT 126 lb (57 kg)
      ENGINE OPTION Honda GX100 3 hp (2.2 kw)
      COMPACTION FORCE Up to 3100 lbf (up to 13.8 kN)
      TRAVEL SPEED Up to 55 ft/min (16 m/min)
      COMPACTION DEPTH Up to 18 in (45 cm)

      GP1800

      Vibratory Plates
      AP2000 SERIES
      Mbw's Ap2000 Series is the only vibratory plate compactor specifically designed for asphalt applications. Frequency, amplitude, centrifugal force and mass are all established at optimal levels for maximum productivity on asphalt.


      Specifications AP200H
      ENGINE Honda GX160 5.5 hp (4.1 kw)
      OPERATING WEIGHT 175 lb (79 kg)
      PLATE SIZE WxL 19 x 21 in (48 x 53 cm)
      CENTRIFUGAL FORCE 2475 lbf (11kN)
      EXCITER SPEED 4400 vpm
      COMPACTION DEPTH 12 in (31 cm)
      TRAVEL SPEED 90 ft/min (27.4 m/min)
      COMPACTION AREA 8550 sqft/h (794 sqm/h)

      AP 2000 Series

      Rollers

      BACK TO TOP OF PAGE

                                               
      Air Compressors  

      4 Cylinder Compressor

      Aerial Lifts  

       

       

       

       
      A-1 Plank & Scaffold-Aluma-Pole-Bosch-Carolina Ladders-ColemanCable-DeltaJobox-DewaltDiamondProducts-Greenbull-Hitachi-Kraft-MBW-Milwaukee-Quincy-Rack-it-Relton-Rustgo-Stabil-Stihl-Stone-Stow-SafetyHoist-VirginiaAbrasives-Weatherguard-Werner-Wing-Yamaha
        ABRASIVE BLADES    ADJ ROOF BRACKET    AERIAL LIFTS    AIR COMPRESSORS    ALUM-A-POLE    ALUMINUM LADDERSBETA MAX HOISTS COMPACTION EQUIP     CONCRETE SAW BLADES     CONCRETE MIXERS    CONSTR EQUIPMENT    CUT-OFF SAWS    FIBERGLASS LADDERS    GENERATORS    GREEN BULL LADDERS    HOISTS     HOIST ACCESSORIES    HOIST MOUNT    LADDER RACK    LADDERS    LITTLE GIANT LADDER    MIXERS    MORTAR MIXERS    PAINT SPRAYERS    PRESSURE WASHERS    PUMP JACK SYSTEMS     ROOF BRACKETS RUSTGO WORK PLATFO     SAFETY EQUIPMENT    SCAFFOLDING    SCAFFOLDING ACCESS    SHORING ACCESSORIES    SHORING FRAMES   TROWELS   VAN RACK   VIBRATORY PLATES    WHEELBARROWS    WALL & LADDER JACKS    USED EQUIPMENT

      About our Scaffolding

      All of our scaffold and scaffolding related products are High Quality Brand New Products. They are all designed to meet or exceed all OSHA, ANSI, and SIA Standards.

      Sunbelt Scaffolding & Supply sells high quality Scaffolding and related products. We carry many types and sizes of frames including S-Style  (1-11/16"o.d.) and W-Style (1 5/8" o. d.), as well as  Veneer Jacks and Shoring Frames We also carry five, six, eight and ten foot  Cross Braces, several different style and sizes of scaffolding boards and scaffold planks including, eight, ten , twelve and sixteen foot, Di-65 OSHA  compliant,  Southern Yellow Pine Scaffolding Planks as well as seven and ten foot Aluminum-Plywood Scaffold Planks and seven and ten foot All Aluminum Scaffold Planks.   We also carry eight, ten, twelve and 16 foot Laminated planks.  We carry all kinds of Jacks including, Scaffold Screw Jacks with base plates, Scaffold Jacks with Sockets, Scaffold Base Plates, Scaffold Swivel Base Plates, Scaffold Swivel Jacks and High Load Scaffold Jacks. We also carry Scaffolding Wheels Casters  including 5"  Casters with a 1 1/4" square shank (for the Aluminum Bakers Style Scaffold and Steel Bakers Scaffold and  8" Scaffold Casters with a 1 3/8" round shank for the standard Masons Style Scaffolding.  We carry Scaffolding Accessories such as Snap Pins, Hinge Pins,  Spring Retainers,   Gravity Pins,  Rivets and Cotters,  Roll Pins, Snap Pins, 1.625  Connecting Pins, 1.690 Connecting Pins, Right Angle Clamps, Swivel Clamps, Hoist Assemblies and  Wheel Wells.  If you need extra working space, our  Scaffolding Side Brackets and  Scaffolding End Brackets,  allow to to work outside the normal standing area, enabling you to reach areas that may not normally be accessible due to an  obstruction at the base of the scaffolding.  For your safety,  We offer many items, such as  Swing Gates,  Expandable Gates Guard Rails Posts,  five, seven, eight and 10 foot Scaffolding Guard Rails.  For accessibility, We carry 3 foot, 5 foot , and 6 foot Scaffolding Ladders, Ladder Brackets, and Internal Scaffolding Stair Units.

                       

       

       


       

       

       

      <script type="text/javascript">
      document.write(unescape("%3Cscript src='" + document.location.protocol + "//www.webtraxs.com/trxscript.php' type='text/javascript'%3E%3C/script%3E"));
      </script>
      <script type="text/javascript">
      _trxid = "sunbeltscaffolding";
      webTraxs();
      </script>
      <noscript><img src="http://www.webtraxs.com/webtraxs.php?id=sunbeltscaffolding&st=img" alt=""></noscript>

      Site created by ThomasNet Web Solutions, a division of ThomasNet.com
      Company Name - Your Tagline Here